Two token upgrades, two different prep routines
Bear Trap (6) and Shield Tokens solve different tabletop problems, and they arrive in different states. The bear traps are 3D printed and sold unpainted, so they need finishing before they hit the table. The shield tokens are cut acrylic and may arrive with protective paper backing on both sides, so they need a quick peel before use. Neither is a drop-in replacement for cardboard, but both are simple to prepare once you know the steps.
This guide walks through what each set contains, how to finish the bear traps, how to clean the acrylic shields, and where each token actually fits in play.
What you get in each pack
- Bear Trap (6): Includes 6 3D-printed bear trap tokens, each measuring 30mm x 24mm x 6mm. Six traps is enough to mark a full room of hazards, and the footprint tells you whether they'll crowd a crowded dungeon tile.

Bear Trap (6) - Bear Trap (6): These tokens will not fit in our Organizer for Gloomhaven (ORG050). If you already own that organizer, plan a separate storage spot for the traps rather than assuming they'll nest in the tray.
- Shield Tokens: This is a set of 10 Shield Tokens cut from 1/8" blue transparent cast acrylic, designed for use with KeyForge: Call of the Archons by Fantasy Flight Games. Ten shields covers a typical KeyForge board state, and the transparent blue keeps the tokens readable against card art.

Shield Tokens - Shield Tokens: Acrylic may arrive with protective paper backing on both sides and should be removed before assembly. Leaving the backing on dulls the transparency and can trap adhesive residue, so peel first.
Finishing the 3D-printed bear traps before play
The bear traps are printed at .2mm layer heights on an FDM printer and sold unpainted. The catalog notes that sanding, trimming, and assembly may be required, and recommends a spray primer for a smoother, paint-ready finish. Work in a ventilated space and follow the primer manufacturer's instructions for drying and recoating.
- Inspect and trim: Check each of the six traps for stray print material or rough edges. Trim anything that would snag on a game tile or catch a finger.
- Sand the visible faces: Light sanding smooths layer lines on the top surfaces and jaws. The catalog lists sanding as a possible prep step; keep it gentle so you don't soften the trap's shape.
- Prime before painting: A spray primer is recommended to provide a smoother, paint-ready finish. Prime in thin passes and let each coat dry fully before the next.
- Paint and seal: The catalog does not specify paint types or sealers. Choose a paint suited to primed plastic and test on one trap before committing to all six.
Cleaning the acrylic shield tokens
The shield tokens are cut from 1/8" blue transparent cast acrylic. The catalog warns that they may arrive with protective paper backing on both sides, which should be removed before assembly. If the paper leaves adhesive behind, Simple Green is recommended to lift the residue.
- Peel both sides: Work a fingernail or a plastic scraper under a corner of the paper and peel slowly. Both faces are covered, so check the token after the first peel.
- Tackle stubborn adhesive: Apply a small amount of Simple Green to a cloth and wipe the acrylic, then rinse and dry. Test on one token first to confirm it doesn't affect the finish.
- Dry before stacking: Water spots and fingerprints dull the transparency. Dry each token fully and stack them only once they're clean.
Which token belongs in which game
The two products are not interchangeable. The bear traps are generic adventure tokens meant to replace stock cardboard game elements or add detail to a tabletop RPG. The shield tokens are a third-party accessory designed specifically for KeyForge: Call of the Archons. Match the token to the game you're actually playing.
- Dungeon crawls and RPGs: Use the bear traps as physical hazard markers on the map. At 30mm x 24mm x 6mm each, they read clearly from across the table and sit on top of most tiles without hiding the artwork.
- KeyForge: Call of the Archons: The shield tokens track shield status on creatures. The blue transparent acrylic keeps them distinct from damage and other counters.
- Gloomhaven storage: The bear traps will not fit in the Organizer for Gloomhaven (ORG050), so keep them in a separate bag or box if you use that organizer.
What the catalog does and doesn't confirm
The catalog confirms the bear traps' dimensions, print method, and unpainted state, plus the Gloomhaven organizer incompatibility. It does not specify a paint brand, primer brand, or drying time, so treat those as choices you make with the products you already have. The shield tokens' catalog entry confirms the material, thickness, count, and KeyForge compatibility, but does not list a storage solution or a cleaning schedule. Both products are made in the USA and are third-party accessories; all product names are trademarks of their respective owners, which are in no way associated or affiliated with The Broken Token.
If you're upgrading a dungeon crawl, the bear traps are the more involved purchase because of the finishing work. If you're upgrading KeyForge, the shields are ready after a peel and a wipe.



